I bought a Baby Trend Expedition jogger stroller at a rummage sale. I looked at their website and know it's definitely not their newest models.
I cannot figure out how to adjust the reclining seat. Right the seat is all the way reclined and it worked great for my son when he was a baby but now as a toddler, he wants to sit up and see things.
The only thing behind the seat is a strap and buckle but I can't see anyway to adjust this to tighten or loosen it. Anyone have any idea how the seat can be adjusted?How can I adjust the seat in my jogger stroller?You need to figure out which model you have and google it. Can you loose the strap? You usally loosen it to lower the seat and tighten it to put the seat up.
Friday, June 3, 2011
How to properly adjust a pendulum clock?
I've got a wind-up pendulum clock (says %26quot;Regulator%26quot; on the glass) that doesn't keep the right time. You can adjust the bob's distance by turning a nut. Does anyone know how to precisely synchronize these things or point me to instructions? There has to be a better way than trial-and-error.How to properly adjust a pendulum clock?I have no idea what the distance should be from the center of rotation to the center of mass of the bob, because that depends on how fast it's supposed to tick. Anyway, I don't think you need an absolute length to adjust to but a relative length change to use in adjusting. The period is roughly proportional to sqrt(length). So if the clock is running, say 1% slow, you need to shorten the distance by ~2%. (The square root of a value that changes slightly, by a factor of 1卤螖, is close to 1卤螖/2.) This is all %26quot;roughly%26quot; because the simple pendulum equation (period T = 2pi*sqrt(L/g)) assumes that all the moving mass is in the bob, with none on the shaft, whereas in real clocks this isn't true. The less true it is, the larger the distance adjustment you'll need to make.
I suggest you write down the changes you make (in fractions of a nut rotation) and the resulting change in time error. This should help you determine successive adjustment steps.How to properly adjust a pendulum clock?You want the length to be:
9.81/(4*pi^2) = 0.24849m = 24.849 cm
I suggest you write down the changes you make (in fractions of a nut rotation) and the resulting change in time error. This should help you determine successive adjustment steps.How to properly adjust a pendulum clock?You want the length to be:
9.81/(4*pi^2) = 0.24849m = 24.849 cm
How long does skin take to adjust to Benzoyl Peroxide and salicylic acid?
I dont mean using the both of them together, i mean how long does it take skin to adjust to BP, as in how long till dryness and flakyness stops. And how long does it take to adjust to SA?How long does skin take to adjust to Benzoyl Peroxide and salicylic acid?BP is stronger for the skin. If you have sensitive skin, I don't recommend it. Even though if you wanna try it, you can start with the product a little amount of the cream, cleanser, whatever, and then growing the amount with time and seeing how your face reacts. Same with SA. And if you have sensitive skin, I recommend of using Acne product that don't have any of both, and they work as same as SA and/or BP.
Hope I helped.
P.
Hope I helped.
P.
How do I adjust the oven temperature when I need to extend the length of cooking?
Hi. I am going to be preparing several pans of baked ziti, but I will not be home for most of the cooking time. Usually they would need a 350 degree oven for 30 minutes, but I need to be gone for at least an hour before they're served. How low should I adjust the heat to allow for this longer cook time?How do I adjust the oven temperature when I need to extend the length of cooking?Just turn it up to desired temp and keep an eye on itHow do I adjust the oven temperature when I need to extend the length of cooking?I'm not sure about adjusting the oven temperature and I don't want to take a guess in case your food gets burnt, so maybe you could try cooking them at their normal temperature for the normal length of time and just reheat them, either in the microwave or in the oven covered in tin foil, before they're due to be served?
Sorry I couldn't be of more help but good luck anyway.How do I adjust the oven temperature when I need to extend the length of cooking?simply turn the temp down by10to15 degrees
Sorry I couldn't be of more help but good luck anyway.How do I adjust the oven temperature when I need to extend the length of cooking?simply turn the temp down by10to15 degrees
How could I adjust the margins of a word document in windows vista?
I tried to adjust it 1 inch for all sides but as I printed the document the bottom of the page is about 1.5 inches.How could I adjust the margins of a word document in windows vista?Are you talking about Microsoft Word? If you look along the left hand side there is a vertical ruler, you will notice the greyed out portion at the bottom, click and drag this down a bit to decrease the margin.
Word does a really weird gutter thing with the bottom of the page.
good luckHow could I adjust the margins of a word document in windows vista?Actually, Word doesn't do a really weird gutter at the bottom of the page, your printer does. Nothing's changed just because it's the latest version, so here's an article that refers to 2003 and below, but still applies.
http://www.officearticles.com/word/troubflooded with viruses medium length hair
Word does a really weird gutter thing with the bottom of the page.
good luckHow could I adjust the margins of a word document in windows vista?Actually, Word doesn't do a really weird gutter at the bottom of the page, your printer does. Nothing's changed just because it's the latest version, so here's an article that refers to 2003 and below, but still applies.
http://www.officearticles.com/word/troub
How do I adjust the nitrate level in my aquarium?
I just did a quick dip stick water test in my aquarium, the nitrate level is in the very hot pink -unsafe. Total hardness is Very Hard. Total alkalinity is low and the PH is acidic. How do i adjust them to normal? and what do I use to do that? Please help my Cichlids are suffering.How do I adjust the nitrate level in my aquarium?First of all, don't try to mess with the pH, alkalinity, or hardness. I have a feeling your testing kit isn't at all accurate, considering how rare it is for to have a low pH and a high alkalinity/buffer. To lessen the nitrates, simply do a 20% water change now, and a 10% water change every other day until the nitrate is below 30 ppm.
You should really consider getting a REAL test kit (liquid instead of strips)... they are quite a bit more accurate.
EDIT: Driftwood makes the water even more acidic, which doesn't appear to be what you need. Also, running the filter will not lower the nitrate as it is the final step in the nitrogen cycle (unless you have denitrifying bacteria, which you don't).How do I adjust the nitrate level in my aquarium?Hi Lisa, messing with your pH will almost never be successful because artificial 'pH up %26amp; down' additives only make the problem worse as they often have a delayed %26amp; cumulative effect so it sways up %26amp; down violently further stressing your fish. Unless the readings are off the scale most fish will tolerate an approximate pH to their own-the most important thing is keeping it stable.
The nitrate reduction is one of the easiest processes in fish keeping-simply do a partial water change using same temperature, treated water. You do a partial water change, you drastically dilute %26amp; reduce your nitrate [%26amp; other toxins] immediately. The good bugs live in your gravel %26amp; filter NOT your water so up to 50% changes daily are perfectly safe.How do I adjust the nitrate level in my aquarium?Simple. Do a water change 25%. This will automatically lower the reading. Also test again tomorrow. You may need to do another water change but drop it to around 20%.
As for the PH:
This is going to sound dumb but what kind of gravel do you have? Believe it or not certain types of gravel will keep your ph from increasing or increase it too much.
The property of water to resist changes in pH is known as buffering capacity. You can determine the capacity of your buffering system by measuring total hardness. A reading of 4-6 dH or higher is usually adequate to keep the buffering system in place and maintain a stable pH. A reading under 4 dH means there isn't enough of a buffering system and the pH is likely to drop. For higher pH levels, you will probably want to aim for 6-12 dH. Many hobbyists choose to measure only Carbonate Hardness (KH), which is a measure of the calcium carbonates in your water. This test is also effective in maintaining a proper buffer system. When testing for Carbonate Hardness, a reading of 75-100 mg/L is adequate for most aquariums, while a reading of 100-200 mg/L would be desired for higher pH levels. For the purpose of freshwater aquariums, measuring either total hardness or carbonate hardness is necessary, but measuring both independently would not be needed.
You need to know that anywhere in your aquarium where detritus (a fancy term for dirt) accumulates is a source of Phosphate production. As detritus accumulates in your gravel bed and on your filter pads, the Phosphate levels in your aquarium rise. Free Phosphate ions may bond with calcareous buffering material, precipitating calcium from your aquarium, and reducing your aquariums ability to keep pH stable. This is why it is so very important to clean your filter pads regularly and vacuum the aquarium gravel with each water change. In addition, your tap water contains buffering ions. Doing regular partial water changes will help to replenish the buffers which have been lost. This is important in all aquariums, because fish respiration and organic wastes alone will cause a gradual drop in the ability of your aquarium to buffer against pH swings.
Now the question becomes what to do if the fish you want to keep have very special pH requirements. If your fish prefer a pH level which is reasonably close to the pH your aquarium water is naturally buffered to, then I do not recommend you make any changes at all. Unless you are keeping an extremely specialized fish your fish will be fine. On the other hand, if your fish have pH requirements which are far from the values in your tank, then you have work to do.
Let us consider methods of raising the pH of your tap water. There are many additives on the market today which claim to raise your pH. Most of the liquid products on the market today are a 50/50 success at best when used alone only to find the ph will soon return to the normal level of 6. You also need to use a product to increase the buffering ability of your aquarium. To maintain a stable pH in the upper levels of the pH scale for fishkeeping, I would recommend using a buffering substrate such as crushed coral. You can add crushed coral to your existing aquarium. You can place larger amounts of shells or chrushed coral beneath the substraight in the tank. I personally place the crushed coral in a mesh bag and place the bag in my filter. You will want about 1 kg of crushed coral per 40 liters of water to buffer the water to hold a pH around 7.6. This method does not allow for the use of large quantities of crushed coral, but can be effective if you only need to make small adjustments to your aquariums buffering ability. This is why ocean items such as shells and ocean sand should not be used in a fresh water aquarium. It does raise the PH level.
Be assured that attempting to control pH is the most frustrating experience for a fish hobbyist. I would guess that 50% of the problems encountered in new aquariums are a result of the aquarist attempting to change the pH level. Few fish keepers actually need to adjust their pH. For the majority of aquarists your tap water pH will be adequate. The dangers of adjusting the pH incorrectly far outweigh any benefit you may receive by moving your pH a few points on the scale.
Remember, when it comes to adjusting your pH, less is more! Stability is most important. Routine maintenance is the key to keeping your pH stable and your fish healthy!
Also, do not use baking soda in your tank. Over doing the ph plus adding additional salt is not going to do your tank any good. It will also revert back to 6 when the carbon filters pull the Soda out.
Hope this helpsHow do I adjust the nitrate level in my aquarium?do a 20% water change. and small changes until the nitrates have dropped to a safe level do a 20% every two weeks.How do I adjust the nitrate level in my aquarium?ph get drift wood from petco
for the rest just run the filter for a few days and for the rest of it just get 1 or 2 fish to get the cycle going after about a week you should see some results
You should really consider getting a REAL test kit (liquid instead of strips)... they are quite a bit more accurate.
EDIT: Driftwood makes the water even more acidic, which doesn't appear to be what you need. Also, running the filter will not lower the nitrate as it is the final step in the nitrogen cycle (unless you have denitrifying bacteria, which you don't).How do I adjust the nitrate level in my aquarium?Hi Lisa, messing with your pH will almost never be successful because artificial 'pH up %26amp; down' additives only make the problem worse as they often have a delayed %26amp; cumulative effect so it sways up %26amp; down violently further stressing your fish. Unless the readings are off the scale most fish will tolerate an approximate pH to their own-the most important thing is keeping it stable.
The nitrate reduction is one of the easiest processes in fish keeping-simply do a partial water change using same temperature, treated water. You do a partial water change, you drastically dilute %26amp; reduce your nitrate [%26amp; other toxins] immediately. The good bugs live in your gravel %26amp; filter NOT your water so up to 50% changes daily are perfectly safe.How do I adjust the nitrate level in my aquarium?Simple. Do a water change 25%. This will automatically lower the reading. Also test again tomorrow. You may need to do another water change but drop it to around 20%.
As for the PH:
This is going to sound dumb but what kind of gravel do you have? Believe it or not certain types of gravel will keep your ph from increasing or increase it too much.
The property of water to resist changes in pH is known as buffering capacity. You can determine the capacity of your buffering system by measuring total hardness. A reading of 4-6 dH or higher is usually adequate to keep the buffering system in place and maintain a stable pH. A reading under 4 dH means there isn't enough of a buffering system and the pH is likely to drop. For higher pH levels, you will probably want to aim for 6-12 dH. Many hobbyists choose to measure only Carbonate Hardness (KH), which is a measure of the calcium carbonates in your water. This test is also effective in maintaining a proper buffer system. When testing for Carbonate Hardness, a reading of 75-100 mg/L is adequate for most aquariums, while a reading of 100-200 mg/L would be desired for higher pH levels. For the purpose of freshwater aquariums, measuring either total hardness or carbonate hardness is necessary, but measuring both independently would not be needed.
You need to know that anywhere in your aquarium where detritus (a fancy term for dirt) accumulates is a source of Phosphate production. As detritus accumulates in your gravel bed and on your filter pads, the Phosphate levels in your aquarium rise. Free Phosphate ions may bond with calcareous buffering material, precipitating calcium from your aquarium, and reducing your aquariums ability to keep pH stable. This is why it is so very important to clean your filter pads regularly and vacuum the aquarium gravel with each water change. In addition, your tap water contains buffering ions. Doing regular partial water changes will help to replenish the buffers which have been lost. This is important in all aquariums, because fish respiration and organic wastes alone will cause a gradual drop in the ability of your aquarium to buffer against pH swings.
Now the question becomes what to do if the fish you want to keep have very special pH requirements. If your fish prefer a pH level which is reasonably close to the pH your aquarium water is naturally buffered to, then I do not recommend you make any changes at all. Unless you are keeping an extremely specialized fish your fish will be fine. On the other hand, if your fish have pH requirements which are far from the values in your tank, then you have work to do.
Let us consider methods of raising the pH of your tap water. There are many additives on the market today which claim to raise your pH. Most of the liquid products on the market today are a 50/50 success at best when used alone only to find the ph will soon return to the normal level of 6. You also need to use a product to increase the buffering ability of your aquarium. To maintain a stable pH in the upper levels of the pH scale for fishkeeping, I would recommend using a buffering substrate such as crushed coral. You can add crushed coral to your existing aquarium. You can place larger amounts of shells or chrushed coral beneath the substraight in the tank. I personally place the crushed coral in a mesh bag and place the bag in my filter. You will want about 1 kg of crushed coral per 40 liters of water to buffer the water to hold a pH around 7.6. This method does not allow for the use of large quantities of crushed coral, but can be effective if you only need to make small adjustments to your aquariums buffering ability. This is why ocean items such as shells and ocean sand should not be used in a fresh water aquarium. It does raise the PH level.
Be assured that attempting to control pH is the most frustrating experience for a fish hobbyist. I would guess that 50% of the problems encountered in new aquariums are a result of the aquarist attempting to change the pH level. Few fish keepers actually need to adjust their pH. For the majority of aquarists your tap water pH will be adequate. The dangers of adjusting the pH incorrectly far outweigh any benefit you may receive by moving your pH a few points on the scale.
Remember, when it comes to adjusting your pH, less is more! Stability is most important. Routine maintenance is the key to keeping your pH stable and your fish healthy!
Also, do not use baking soda in your tank. Over doing the ph plus adding additional salt is not going to do your tank any good. It will also revert back to 6 when the carbon filters pull the Soda out.
Hope this helpsHow do I adjust the nitrate level in my aquarium?do a 20% water change. and small changes until the nitrates have dropped to a safe level do a 20% every two weeks.How do I adjust the nitrate level in my aquarium?ph get drift wood from petco
for the rest just run the filter for a few days and for the rest of it just get 1 or 2 fish to get the cycle going after about a week you should see some results
How do I adjust the flame on my mega pocket torch?
I just found an ancient mega pocket torch... It looks like the new models though lol. Anyways I know where you fill it, but I just want to know how to adjust the flame on it?How do I adjust the flame on my mega pocket torch?just adjust gaz flow
How do you adjust to a friends with benefits relationship?
I just kind of started one. We didn't do anything yet but how to adjust to it? How do we start?How do you adjust to a friends with benefits relationship?Stick your hand down his pants. That should speed things up.How do you adjust to a friends with benefits relationship?Just kind of meet up hang out and what happens happensHow do you adjust to a friends with benefits relationship?you can't treat them like a real boy/girlfriend. live your life as usual and see them when you see them, for a lil fun!
How do you adjust notifications from facebook on blackberry?
I don't want to receive a notification every time someone writes on my wall or sends me a message. How do I stop this? I went to my facebook settings for notifications, but that only tells me about notifications by email, I couldn't find where I adjust notifications on my mobile device.How do you adjust notifications from facebook on blackberry?Go into Facebook for BB - then go into the Notifications icon
Press the Menu key - click Options
Clear the BlackBerry messages application check box - Save.
Press the Menu key - click Options
Clear the BlackBerry messages application check box - Save.
How do you adjust the brightness of your computer screen without using the monitor?
I am running XP on my desktop. I know how to do adjust brightness on the monitor, but the brightness is up full blast and the screen is still dark. I downloaded the XP applet for color management and its no good (of course) I have a nvidia graphics card but for some reason the control panel won't work and freezes the system. Is there a free program I can download to manage my color settings?How do you adjust the brightness of your computer screen without using the monitor?perhaps it is not possibleHow do you adjust the brightness of your computer screen without using the monitor?You should first download the newest drivers for your video card. The Nvidia control panel will do what you want. It is called Gamma. http://www.aquiladigital.us/ get DarkAdapted if you want to use freeware instead.bird how to break up with someone you love
How do you adjust the resolution on a picture already taken?
I am trying to buy birth announcements online, but they are telling me that the resolution is too low and I need to adjust it then upload it again? Is that even possible w/o Photoshop? How do you adjust the resolution on a picture already taken?yeah, photoshop,
change your image size to around 200dpi in image then size.
then go file save for web, adjust the size to around 35k, you do this with the toolbox on your right hand side where it says jpeg lo-high,
35k is usually standard for web.How do you adjust the resolution on a picture already taken?there are much simpler and free image editors. search in www.softpedia.com
change your image size to around 200dpi in image then size.
then go file save for web, adjust the size to around 35k, you do this with the toolbox on your right hand side where it says jpeg lo-high,
35k is usually standard for web.How do you adjust the resolution on a picture already taken?there are much simpler and free image editors. search in www.softpedia.com
How do i adjust/locate the governor on a tecumseh 6 hp go cart engine?
I have a gocart with a tecumseh 6 hp engine, I want to adjust to governor to make it faster.How do i adjust/locate the governor on a tecumseh 6 hp go cart engine?use a straightened paper clip or a piece of stiff wire to bypass the spring on the linkage
be careful if you over rev it it will blow
be careful if you over rev it it will blow
How can I adjust my skunk2 coilovers with out the adjustment key?
I lost the key that unlocks and locks them. I need some ideas of how to adjust them without lookig for another key.How can I adjust my skunk2 coilovers with out the adjustment key?the best thing to do would probably call skunk2 motorsports and ask them
How do I adjust the headlights on my 2003 cobra?
It appears that my right headlight is tiltied up a bit and I cannot find the screw to adjust it. Where is this located? I assume it will be the same for 2003-2004 Mustangs as well.How do I adjust the headlights on my 2003 cobra?there may be a dust cover in the way of the adjustment screws is there a panel to remove either ebouve or to the side of the light assebly? possibly under the hood?
How do you adjust a clutch cable on a 2000 mitsubishi eclipse gs?
It is harder than normal to shift into gears and i was told you adjust the cable on my clutch. Should I loosen or tighten?How do you adjust a clutch cable on a 2000 mitsubishi eclipse gs?2000 Eclipse doesn't use a cable clutch system. It runs off hydraulics (ie- clutch master cylinder, clutch slave cylinder). Flushing and bleeding the clutch fluid and change the fluid in the trans.How do you adjust a clutch cable on a 2000 mitsubishi eclipse gs?Like he said, it is all clutch fluid. Buy some dot 3 brake fluid, and fill your master cylinder up. You are going to have to look on your transmission, there should be a little nipple type looking thing, and you should be able to actually hook a small air hose up to it. I used a clear hose that i found that would fit it correctly. Then what you do is take a item that can hold liquids, I.E. Gatorade bottle, and fill that up with brake fluid. have one end of the hose on your trans, and the other in the cup/bottle, and make sure it is submerged under completely. Have someone go in the car, and depress the clutch completely to the floor, and tell them to lift it up slowly. when it is completely up, put the cap back on the trans, and you should have a firm clutch pedal.stop severe facial sweating can't calibrate printer
How can i adjust the voice clarity and volume in my Nokia 3210 classic mobile phone?
I am having a real problem hearing the callers voice on my phone and I have tried to adjust the clarity but am noticing no difference. Any suggestions?How can i adjust the voice clarity and volume in my Nokia 3210 classic mobile phone?While on a call, just try increasing the volume via the side buttons or try using the scroll keys. Like press the up or right scroll key. This might help.
How do you adjust withholdings on your pay check?
I am a recent college grad who just accepted a job. I received a signing bonus, but 40% was taken out for tax. My job startes in August, so I would like to adjust my withholdings to make my paycheck bigger to compensate for the tax that I already paid through my bonus. What is the best plan of action?How do you adjust withholdings on your pay check?Determine your gross salary and adjust withholding so that at the end of the year you are even . No interest free loan for the government and you use your money all year long.How do you adjust withholdings on your pay check?talk to your company's accounting dept., if you have one. (If not, try the administrative assistant or HR department.) I believe it's the W-4 form that lets you adjust this allowance.How do you adjust withholdings on your pay check?You might need to talk to a financial planner to see how to reduce your tax liability.How do you adjust withholdings on your pay check?You can pick up a W4 form from your human resources department and re-do your percentages and additional amounts that you want changed. Also the more dependents you are able to claim, the less the IRS will take out of your check BUT in doing that, you may end up owing taxes at the end of the year. If still in doubt, you should be able to find a CPA in the area who can give you some advice based on your own personal situation.How do you adjust withholdings on your pay check?go to your HR department and fill out a new W-4How do you adjust withholdings on your pay check?It will depend on the amount of allowances you claim on your W-4's. For each allowance you claim, they will deduct 3300 divided by the number of pay periods in a year from your check. For instance, if your pay is biweekly, 3300/26=$126.92. They will take the remaining amount from the check depending on how much you make. If you are single, and on a biweekly pay, generally it's 10% up to $385 then 15% up to $1240 and then 25% up to $2817. You can claim as many allowances as you like, and have none withheld at all, but just note that 90% of your tax due must be paid by year's end by withholdings or estimated payments.
How do you adjust a glass office door to keep from dragging?
We have a full view glass entry door on our building that is hitting on bottom and won't close completely. Is there some way to adjust the arm etc..to pull the door back up to close?How do you adjust a glass office door to keep from dragging?You have a herculite glass door or a tempered glass and aluminum door.
If its a herculite door and is rubbing do not use the door and get someone who works on doors (maintenance , glass house , door repair company) as these doors can %26quot;blow up%26quot; if enough force is put upon the edge, and all you'll have is a loud bang and a pile of glass squares on the floor.Don't try to pry on it either as it may give the same effect.
Pivots may need adustment/replacement,door arm may need to be shimmedreplaced, threshold area may be shifting.How do you adjust a glass office door to keep from dragging?I would contact either the building contractor or if the building is old the building maintenance people. Glass doors are extremely heavy and very dangerous to mess with unless you know what you are doing.How do you adjust a glass office door to keep from dragging?A maintenance man or a professional glass fitter.How do you adjust a glass office door to keep from dragging?Check to see if your hinges are loose......Or call a professional and write it off on taxes, or maintenance if your renting........How do you adjust a glass office door to keep from dragging?I`m sure if you can afford an office with glass doors, you can afford proffessional service and repair!!!
If its a herculite door and is rubbing do not use the door and get someone who works on doors (maintenance , glass house , door repair company) as these doors can %26quot;blow up%26quot; if enough force is put upon the edge, and all you'll have is a loud bang and a pile of glass squares on the floor.Don't try to pry on it either as it may give the same effect.
Pivots may need adustment/replacement,door arm may need to be shimmedreplaced, threshold area may be shifting.How do you adjust a glass office door to keep from dragging?I would contact either the building contractor or if the building is old the building maintenance people. Glass doors are extremely heavy and very dangerous to mess with unless you know what you are doing.How do you adjust a glass office door to keep from dragging?A maintenance man or a professional glass fitter.How do you adjust a glass office door to keep from dragging?Check to see if your hinges are loose......Or call a professional and write it off on taxes, or maintenance if your renting........How do you adjust a glass office door to keep from dragging?I`m sure if you can afford an office with glass doors, you can afford proffessional service and repair!!!
How do you adjust hydraulic disc brakes on a mountain bike?
I need to adjust my front caliper, it's a little tight, but I am not sure how to even go about that. I have Tektro Auriga Comp hydro brakes. Diagrams or detailed videos would be most helpful because I really don't know the names of each part on the caliper.How do you adjust hydraulic disc brakes on a mountain bike?Download the owners manual.
http://www.tektro.com/04support/manual.p
This may also help to give you an idea what to do.
http://www.parktool.com/repair/byregion.
http://www.tektro.com/04support/manual.p
This may also help to give you an idea what to do.
http://www.parktool.com/repair/byregion.
How do you adjust a temperature control faucet?
I installed a temperature control faucet about 2 months ago. It was working fine but now the hot water is becoming less and less( almost cold ) I know their has to be a way to adjust this thing. Has anybody out there ever worked with one of these things?How do you adjust a temperature control faucet?Remover the handle, behind the handle will be a disk with two arrows, depending on the brand, this will advance it to hotter or colder. If no small children are living in the house, adjust it all the way to hot. If not, buy a thermometer, and check to make sure the water temp, it at 105 degrees maximum per the national plumbing code.hardware in the future
How do I adjust the tempature on our gas oven?
I am using a gas oven for the first time and we can't seem to adjust the temp. We can turn it on, it goes up to about 475 and it seems the only way to turn it down is to turn it off. Has anyone had this problem before?How do I adjust the tempature on our gas oven?Modern gas ovens have an automatic thermostat just like electric ovens. Old ones, you have to adjust the flame via a pilot switch. It's usually inside the oven, top center.How do I adjust the tempature on our gas oven?is there no adjustable thermostat with all the other temp's as options?
is this a new oven with fancy controls or a older oven.How do I adjust the tempature on our gas oven?Use the knobHow do I adjust the tempature on our gas oven?Your booklet will tell you how to do it. Ours is very involved, we finally bought a new stove.
Check out this website:
http://www.ehow.com/how_8260_check-adjus
is this a new oven with fancy controls or a older oven.How do I adjust the tempature on our gas oven?Use the knobHow do I adjust the tempature on our gas oven?Your booklet will tell you how to do it. Ours is very involved, we finally bought a new stove.
Check out this website:
http://www.ehow.com/how_8260_check-adjus
How should one adjust watering of Italian Cypress trees from summer to winter and back again?
How should one adjust watering of Italian Cypress trees from summer to winter and back again?
The reason I am asking is due to my noticing some of these trees (in the ground for 2 1/2 years) are now prone to leaning from the effect of strong winds--and needing to be tied.
My question is: should the summer watering be less frequent, but deeper (longer)? Do these conifers extend roots downward in the summer? I notice there is little to no top growth in summer. These trees are located in the Sonoran Desert of Arizona.How should one adjust watering of Italian Cypress trees from summer to winter and back again?.
The reason I am asking is due to my noticing some of these trees (in the ground for 2 1/2 years) are now prone to leaning from the effect of strong winds--and needing to be tied.
My question is: should the summer watering be less frequent, but deeper (longer)? Do these conifers extend roots downward in the summer? I notice there is little to no top growth in summer. These trees are located in the Sonoran Desert of Arizona.How should one adjust watering of Italian Cypress trees from summer to winter and back again?.
How do you adjust quickly to a new school with new people and a campus?
I just started 9th grade and only one guy from my middle school is here. So many new people, new campus, new classes, so how do I adjust to all this quickly?How do you adjust quickly to a new school with new people and a campus?well you could try joining in you can join some teams get to know people better
How can I adjust the fuel gauge on an oil tank?
The fuel gauge for my oil tank, a Granby, is off by about 1/4 of a tank. Everytime the oil company comes to fill it, the gauge stops at a little over 3/4 of a tank; and, yes, I can do the math and realize that when it's near %26quot;E%26quot;, there's really only 1/4 tank left of oil. BUT, I still want to adjust it.
Is this something I can do myself, and if so how, or should I just have the oil company do it?
Oh, the guage is on top of the tank. It's a glass tube with a disc attached to the top of a tiny rod inside that gradually lowers as the oil is depleted.How can I adjust the fuel gauge on an oil tank?Your sending unit inside the tank is bad and needs to be replaced. there is no way to adjustHow can I adjust the fuel gauge on an oil tank?take it out an clean it an make shure it moves along the rod.How can I adjust the fuel gauge on an oil tank?there is no adjustment for these gauges, if it does not work properly the only way to fix it is to replace it. sorry
Is this something I can do myself, and if so how, or should I just have the oil company do it?
Oh, the guage is on top of the tank. It's a glass tube with a disc attached to the top of a tiny rod inside that gradually lowers as the oil is depleted.How can I adjust the fuel gauge on an oil tank?Your sending unit inside the tank is bad and needs to be replaced. there is no way to adjustHow can I adjust the fuel gauge on an oil tank?take it out an clean it an make shure it moves along the rod.How can I adjust the fuel gauge on an oil tank?there is no adjustment for these gauges, if it does not work properly the only way to fix it is to replace it. sorry
How do I adjust the handbrake on a 2002 skoda octavia?
I've replaced the rear discs and pads and now need to adjust the handbrake does anyone know how to do it?How do I adjust the handbrake on a 2002 skoda octavia?If you look in between the two front seats you will see a round bar shaped device. If you pull/push on it it adjusts the handbrake up and down!! ;-)How do I adjust the handbrake on a 2002 skoda octavia?its a skoda-just let it roll awayclear nail polish wheat germ oil
How do I adjust cooking time for 4700 Feet?
I am baking cookies, do I need to adjust the time for this elevation ?How do I adjust cooking time for 4700 Feet?Most cookies are baked by sight, so take them out when they look to be as done as you want them. If they are spreading too much, raise the oven temp by 25 deg F. Your cookies will probably be done sooner than they would be at sea level, yes, both because of the higher temp, and the more rapid evaporation of water at higher altitudes. Start checking them at about 2/3 of the time stated in the recipe.
I bake at 4000 ft.How do I adjust cooking time for 4700 Feet?each oven is different, so just keep an eye on your baking. the most important thing to remember is that your cookies will be dryer at a higher altitude. you can accomodate this by adding a bit more liquid. you will have to experiment to know for sure what works with each recipe.How do I adjust cooking time for 4700 Feet?From the Crisco website:
Baking at high altitude
Atmospheric pressure is less at high altitudes than at sea level or more normal elevations.
This lower pressure affects the baking of cakes in several ways.
* Heat rises from the bottom of an oven, but since there isn't sufficient air pressure from above to balance this upward pressure, the cake tends to expand too rapidly.
* Air cells in the cake can break and escape because of this too-rapid expansion, resulting in a cake that will dip or fall.
* Batter may overflow the pan due to the too-rapid expansion of the cake.
* Cakes can remain underdone if temperature is not raised to adjust for the lower boiling point at high altitudes.
* Due to rapid evaporation of liquids at high altitudes, cakes must be carefully timed to avoid excess dryness.
High-altitude conversion tips
To convert standard recipes into those that can be used for high-altitude baking:
* Use 5% more flour to disperse the leavening action and slow down the rapid rise of the cake.
* Use 20% more water to counterbalance the rapid evaporation of liquids at high altitudes and the extra flour added to the cake batter
* Bake about 25 degrees higher to help %26quot;set%26quot; the cake's crust
* Reduce baking time by about 20% to prevent overbaking at the higher temperature
* Fill pans 1/3 to no more than 1/2 full to avoid batter overflow caused by rapid cake expansion.
* Use cold water and large, cold eggs to give cake extra strength
* Generously grease and flour cake pans to prevent cake from sticking
* Remove top oven rack to prevent cake from sticking to it, since high-altitude cakes rise higher
* Have oven calibrated by a serviceperson periodically, since some thermostats are affected by altitude
High-altitude cookie adjustment
Only cookies with lots of chocolate, nuts, or dates need adjustment: Reduce baking powder/soda by 1/2.
I bake at 4000 ft.How do I adjust cooking time for 4700 Feet?each oven is different, so just keep an eye on your baking. the most important thing to remember is that your cookies will be dryer at a higher altitude. you can accomodate this by adding a bit more liquid. you will have to experiment to know for sure what works with each recipe.How do I adjust cooking time for 4700 Feet?From the Crisco website:
Baking at high altitude
Atmospheric pressure is less at high altitudes than at sea level or more normal elevations.
This lower pressure affects the baking of cakes in several ways.
* Heat rises from the bottom of an oven, but since there isn't sufficient air pressure from above to balance this upward pressure, the cake tends to expand too rapidly.
* Air cells in the cake can break and escape because of this too-rapid expansion, resulting in a cake that will dip or fall.
* Batter may overflow the pan due to the too-rapid expansion of the cake.
* Cakes can remain underdone if temperature is not raised to adjust for the lower boiling point at high altitudes.
* Due to rapid evaporation of liquids at high altitudes, cakes must be carefully timed to avoid excess dryness.
High-altitude conversion tips
To convert standard recipes into those that can be used for high-altitude baking:
* Use 5% more flour to disperse the leavening action and slow down the rapid rise of the cake.
* Use 20% more water to counterbalance the rapid evaporation of liquids at high altitudes and the extra flour added to the cake batter
* Bake about 25 degrees higher to help %26quot;set%26quot; the cake's crust
* Reduce baking time by about 20% to prevent overbaking at the higher temperature
* Fill pans 1/3 to no more than 1/2 full to avoid batter overflow caused by rapid cake expansion.
* Use cold water and large, cold eggs to give cake extra strength
* Generously grease and flour cake pans to prevent cake from sticking
* Remove top oven rack to prevent cake from sticking to it, since high-altitude cakes rise higher
* Have oven calibrated by a serviceperson periodically, since some thermostats are affected by altitude
High-altitude cookie adjustment
Only cookies with lots of chocolate, nuts, or dates need adjustment: Reduce baking powder/soda by 1/2.
How do I adjust the spring tension on a garage door?
I have a garage door on my garage, but it's very heavy. There is a large spring to balance it, but I don't know how to adjust it. How can I make it easier to open and close?How do I adjust the spring tension on a garage door?remove the spring with the garage door in the open (up) position. be sure to prop the door up beforehand so the door doesn't automatically drop down on you. you can add steel rings to make it longer, or purchase a longer spring. it's pretty easy job once you try it slow and safe.How do I adjust the spring tension on a garage door?Personally, if your not really mechanically inclined,I would hire someone to do it.Those springs store an amazing amount of energy.I am definitely not knocking your intelligence,just saying be very careful.I have a good buddy that got his hand broke in one of those things when it decided to cut loose.Best of luck.How do I adjust the spring tension on a garage door?If you have not been trained or know exactly how your systems works, DON'T TRY IT!
Things will go wrong very fast and there is a potential for death.
That being said, even if you adjusted the door, if not done properly will ruin your door opener, and you will have a poorly operating door to deal with, not very convenient.
Springs get weak towards the end of their life expectancy. If you springs are more than 8 years old and and losing power, have them replaced. Most companies change spring for a flat rate, cheaper than an emergency repair.How do I adjust the spring tension on a garage door?I am a do it yourselfer myself, but I stress the importance of having a professional do it. These springs are very powerful and can hurt you. Too much adjustment and you can break the spring and it could definitley hurt you. Leave it to the professionals.How do I adjust the spring tension on a garage door?Depends on what type of spring system you have!!How do I adjust the spring tension on a garage door?DON'T- DON'T- DON'T It could cripple or kill you. Your spring tension didn't change . Look for a jammed roller or track allignment. Call a professional if those are not the problem.
Things will go wrong very fast and there is a potential for death.
That being said, even if you adjusted the door, if not done properly will ruin your door opener, and you will have a poorly operating door to deal with, not very convenient.
Springs get weak towards the end of their life expectancy. If you springs are more than 8 years old and and losing power, have them replaced. Most companies change spring for a flat rate, cheaper than an emergency repair.How do I adjust the spring tension on a garage door?I am a do it yourselfer myself, but I stress the importance of having a professional do it. These springs are very powerful and can hurt you. Too much adjustment and you can break the spring and it could definitley hurt you. Leave it to the professionals.How do I adjust the spring tension on a garage door?Depends on what type of spring system you have!!How do I adjust the spring tension on a garage door?DON'T- DON'T- DON'T It could cripple or kill you. Your spring tension didn't change . Look for a jammed roller or track allignment. Call a professional if those are not the problem.
How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?
Certain notes are giving me a buzzing noise, and my instructor says I should adjust the truss bar a little bit to get rid of it. How do I do this?How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?turn off distortionHow do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?I used to work in a music store, and I saw quite a few people bring in a broken guitar after they tried to adjust the truss rod themselves. If it's a nice guitar, it's worth taking in professionally to have someone who knows what their doing make the adjustment.
I assume your instructor knows what he or she is talking about in terms of what is causing the buzzing. It could be a warped neck, which would be fixed by a truss rod adjustment. Also, the action could be too low, meaning the strings are too close to the neck, so the string hits other frets when you play it creating a buzzing problem. Or, it could be electronics, if you have an electric. These problems are easily fixable, but if you have a nice instrument you want it in the hands of a professional.How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?With the strings off the guitar, you will use a straight edge across the frets. The instruction manual will give you a clearance at a certain fret, you will adjust the truss until those clearances are met. If you haven't done it before, I would take to your guitar shop and have them do it, it won't cost much and you will learn how to do it next time.How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?the bolt at the top of the guitar, on the head, its next to the nut. get the appropriate allen wrench i believe you need, and twist it until the neck of the guitar isnt bowed any more.
I assume your instructor knows what he or she is talking about in terms of what is causing the buzzing. It could be a warped neck, which would be fixed by a truss rod adjustment. Also, the action could be too low, meaning the strings are too close to the neck, so the string hits other frets when you play it creating a buzzing problem. Or, it could be electronics, if you have an electric. These problems are easily fixable, but if you have a nice instrument you want it in the hands of a professional.How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?With the strings off the guitar, you will use a straight edge across the frets. The instruction manual will give you a clearance at a certain fret, you will adjust the truss until those clearances are met. If you haven't done it before, I would take to your guitar shop and have them do it, it won't cost much and you will learn how to do it next time.How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?the bolt at the top of the guitar, on the head, its next to the nut. get the appropriate allen wrench i believe you need, and twist it until the neck of the guitar isnt bowed any more.
How can I adjust the hop up on my air soft gun with out dis assembling the gun?
Crossman Stinger p9. When shot curves up and to the right. Severly. Every once in a wile it is normal. But 3/4 of the time its ridiculous. Can I adjust it without takinga apart the gun.How can I adjust the hop up on my air soft gun with out dis assembling the gun?no unless you have a hop up button check you manual.
How do you adjust a power seat if there was a manual seat there before?
I replaced my broken manual '95 dodge caravan driver's seat w/ a power '99 driver's seat. The wires underneath the seat don't match. Is there an adaptor to make these work together? Is there some way to manually adjust the seat? Is there any problem not having the wire from the floor of the van connected to the seat?How do you adjust a power seat if there was a manual seat there before?you don't need an adapter if had power seats to begin with,you just need the part of the harness that the other seats came from and cut and splice it on the existing wiring harness this way you,ll get power to it,you,ll need the wiring diagrams though for both vehicles to know what wires to hook up though,but really there isn't much to do on that one,power seats are one of the easiest things there is to wire up,most just have a two wire plug one positive wire and one ground wire,on a power seat the only way to adjust it is by running a power source to it,good luck.EDIT if you never had power seat to begin with you may not have the needed wires to install one with,so you,ll probably have to run some power wires to it,good luck.How do you adjust a power seat if there was a manual seat there before?your very welcome. What 360 game to buy get a unique twin duvet cover
Report Abuse
How do you adjust a power seat if there was a manual seat there before?Nope - It's power or nothing. No adapter I've ever seen, %26amp; the wires coming-out of the floor carpet will be fine as they are. You should be able to adapt the new seat wiring to the van wiring with a bit of work.How do you adjust quickly to a new school with new people and a campus?
I just started 9th grade and only one guy from my middle school is here. So many new people, new campus, new classes, so how do I adjust to all this quickly?How do you adjust quickly to a new school with new people and a campus?well you could try joining in you can join some teams get to know people better
How can I adjust the fuel gauge on an oil tank?
The fuel gauge for my oil tank, a Granby, is off by about 1/4 of a tank. Everytime the oil company comes to fill it, the gauge stops at a little over 3/4 of a tank; and, yes, I can do the math and realize that when it's near %26quot;E%26quot;, there's really only 1/4 tank left of oil. BUT, I still want to adjust it.
Is this something I can do myself, and if so how, or should I just have the oil company do it?
Oh, the guage is on top of the tank. It's a glass tube with a disc attached to the top of a tiny rod inside that gradually lowers as the oil is depleted.How can I adjust the fuel gauge on an oil tank?Your sending unit inside the tank is bad and needs to be replaced. there is no way to adjustHow can I adjust the fuel gauge on an oil tank?take it out an clean it an make shure it moves along the rod.How can I adjust the fuel gauge on an oil tank?there is no adjustment for these gauges, if it does not work properly the only way to fix it is to replace it. sorry
Is this something I can do myself, and if so how, or should I just have the oil company do it?
Oh, the guage is on top of the tank. It's a glass tube with a disc attached to the top of a tiny rod inside that gradually lowers as the oil is depleted.How can I adjust the fuel gauge on an oil tank?Your sending unit inside the tank is bad and needs to be replaced. there is no way to adjustHow can I adjust the fuel gauge on an oil tank?take it out an clean it an make shure it moves along the rod.How can I adjust the fuel gauge on an oil tank?there is no adjustment for these gauges, if it does not work properly the only way to fix it is to replace it. sorry
How do I adjust the handbrake on a 2002 skoda octavia?
I've replaced the rear discs and pads and now need to adjust the handbrake does anyone know how to do it?How do I adjust the handbrake on a 2002 skoda octavia?its a skoda-just let it roll awayHow do I adjust the handbrake on a 2002 skoda octavia?If you look in between the two front seats you will see a round bar shaped device. If you pull/push on it it adjusts the handbrake up and down!! ;-)
How do I adjust cooking time for 4700 Feet?
I am baking cookies, do I need to adjust the time for this elevation ?How do I adjust cooking time for 4700 Feet?Most cookies are baked by sight, so take them out when they look to be as done as you want them. If they are spreading too much, raise the oven temp by 25 deg F. Your cookies will probably be done sooner than they would be at sea level, yes, both because of the higher temp, and the more rapid evaporation of water at higher altitudes. Start checking them at about 2/3 of the time stated in the recipe.
I bake at 4000 ft.How do I adjust cooking time for 4700 Feet?each oven is different, so just keep an eye on your baking. the most important thing to remember is that your cookies will be dryer at a higher altitude. you can accomodate this by adding a bit more liquid. you will have to experiment to know for sure what works with each recipe.How do I adjust cooking time for 4700 Feet?From the Crisco website:
Baking at high altitude
Atmospheric pressure is less at high altitudes than at sea level or more normal elevations.
This lower pressure affects the baking of cakes in several ways.
* Heat rises from the bottom of an oven, but since there isn't sufficient air pressure from above to balance this upward pressure, the cake tends to expand too rapidly.
* Air cells in the cake can break and escape because of this too-rapid expansion, resulting in a cake that will dip or fall.
* Batter may overflow the pan due to the too-rapid expansion of the cake.
* Cakes can remain underdone if temperature is not raised to adjust for the lower boiling point at high altitudes.
* Due to rapid evaporation of liquids at high altitudes, cakes must be carefully timed to avoid excess dryness.
High-altitude conversion tips
To convert standard recipes into those that can be used for high-altitude baking:
* Use 5% more flour to disperse the leavening action and slow down the rapid rise of the cake.
* Use 20% more water to counterbalance the rapid evaporation of liquids at high altitudes and the extra flour added to the cake batter
* Bake about 25 degrees higher to help %26quot;set%26quot; the cake's crust
* Reduce baking time by about 20% to prevent overbaking at the higher temperature
* Fill pans 1/3 to no more than 1/2 full to avoid batter overflow caused by rapid cake expansion.
* Use cold water and large, cold eggs to give cake extra strength
* Generously grease and flour cake pans to prevent cake from sticking
* Remove top oven rack to prevent cake from sticking to it, since high-altitude cakes rise higher
* Have oven calibrated by a serviceperson periodically, since some thermostats are affected by altitude
High-altitude cookie adjustment
Only cookies with lots of chocolate, nuts, or dates need adjustment: Reduce baking powder/soda by 1/2.
I bake at 4000 ft.How do I adjust cooking time for 4700 Feet?each oven is different, so just keep an eye on your baking. the most important thing to remember is that your cookies will be dryer at a higher altitude. you can accomodate this by adding a bit more liquid. you will have to experiment to know for sure what works with each recipe.How do I adjust cooking time for 4700 Feet?From the Crisco website:
Baking at high altitude
Atmospheric pressure is less at high altitudes than at sea level or more normal elevations.
This lower pressure affects the baking of cakes in several ways.
* Heat rises from the bottom of an oven, but since there isn't sufficient air pressure from above to balance this upward pressure, the cake tends to expand too rapidly.
* Air cells in the cake can break and escape because of this too-rapid expansion, resulting in a cake that will dip or fall.
* Batter may overflow the pan due to the too-rapid expansion of the cake.
* Cakes can remain underdone if temperature is not raised to adjust for the lower boiling point at high altitudes.
* Due to rapid evaporation of liquids at high altitudes, cakes must be carefully timed to avoid excess dryness.
High-altitude conversion tips
To convert standard recipes into those that can be used for high-altitude baking:
* Use 5% more flour to disperse the leavening action and slow down the rapid rise of the cake.
* Use 20% more water to counterbalance the rapid evaporation of liquids at high altitudes and the extra flour added to the cake batter
* Bake about 25 degrees higher to help %26quot;set%26quot; the cake's crust
* Reduce baking time by about 20% to prevent overbaking at the higher temperature
* Fill pans 1/3 to no more than 1/2 full to avoid batter overflow caused by rapid cake expansion.
* Use cold water and large, cold eggs to give cake extra strength
* Generously grease and flour cake pans to prevent cake from sticking
* Remove top oven rack to prevent cake from sticking to it, since high-altitude cakes rise higher
* Have oven calibrated by a serviceperson periodically, since some thermostats are affected by altitude
High-altitude cookie adjustment
Only cookies with lots of chocolate, nuts, or dates need adjustment: Reduce baking powder/soda by 1/2.
How do I adjust the spring tension on a garage door?
I have a garage door on my garage, but it's very heavy. There is a large spring to balance it, but I don't know how to adjust it. How can I make it easier to open and close?How do I adjust the spring tension on a garage door?remove the spring with the garage door in the open (up) position. be sure to prop the door up beforehand so the door doesn't automatically drop down on you. you can add steel rings to make it longer, or purchase a longer spring. it's pretty easy job once you try it slow and safe.How do I adjust the spring tension on a garage door?Personally, if your not really mechanically inclined,I would hire someone to do it.Those springs store an amazing amount of energy.I am definitely not knocking your intelligence,just saying be very careful.I have a good buddy that got his hand broke in one of those things when it decided to cut loose.Best of luck.How do I adjust the spring tension on a garage door?If you have not been trained or know exactly how your systems works, DON'T TRY IT!
Things will go wrong very fast and there is a potential for death.
That being said, even if you adjusted the door, if not done properly will ruin your door opener, and you will have a poorly operating door to deal with, not very convenient.
Springs get weak towards the end of their life expectancy. If you springs are more than 8 years old and and losing power, have them replaced. Most companies change spring for a flat rate, cheaper than an emergency repair.How do I adjust the spring tension on a garage door?I am a do it yourselfer myself, but I stress the importance of having a professional do it. These springs are very powerful and can hurt you. Too much adjustment and you can break the spring and it could definitley hurt you. Leave it to the professionals.How do I adjust the spring tension on a garage door?Depends on what type of spring system you have!!How do I adjust the spring tension on a garage door?DON'T- DON'T- DON'T It could cripple or kill you. Your spring tension didn't change . Look for a jammed roller or track allignment. Call a professional if those are not the problem.grey hair how to break up with my boyfriend
Things will go wrong very fast and there is a potential for death.
That being said, even if you adjusted the door, if not done properly will ruin your door opener, and you will have a poorly operating door to deal with, not very convenient.
Springs get weak towards the end of their life expectancy. If you springs are more than 8 years old and and losing power, have them replaced. Most companies change spring for a flat rate, cheaper than an emergency repair.How do I adjust the spring tension on a garage door?I am a do it yourselfer myself, but I stress the importance of having a professional do it. These springs are very powerful and can hurt you. Too much adjustment and you can break the spring and it could definitley hurt you. Leave it to the professionals.How do I adjust the spring tension on a garage door?Depends on what type of spring system you have!!How do I adjust the spring tension on a garage door?DON'T- DON'T- DON'T It could cripple or kill you. Your spring tension didn't change . Look for a jammed roller or track allignment. Call a professional if those are not the problem.
How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?
Certain notes are giving me a buzzing noise, and my instructor says I should adjust the truss bar a little bit to get rid of it. How do I do this?How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?turn off distortionHow do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?I used to work in a music store, and I saw quite a few people bring in a broken guitar after they tried to adjust the truss rod themselves. If it's a nice guitar, it's worth taking in professionally to have someone who knows what their doing make the adjustment.
I assume your instructor knows what he or she is talking about in terms of what is causing the buzzing. It could be a warped neck, which would be fixed by a truss rod adjustment. Also, the action could be too low, meaning the strings are too close to the neck, so the string hits other frets when you play it creating a buzzing problem. Or, it could be electronics, if you have an electric. These problems are easily fixable, but if you have a nice instrument you want it in the hands of a professional.How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?With the strings off the guitar, you will use a straight edge across the frets. The instruction manual will give you a clearance at a certain fret, you will adjust the truss until those clearances are met. If you haven't done it before, I would take to your guitar shop and have them do it, it won't cost much and you will learn how to do it next time.How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?the bolt at the top of the guitar, on the head, its next to the nut. get the appropriate allen wrench i believe you need, and twist it until the neck of the guitar isnt bowed any more.
I assume your instructor knows what he or she is talking about in terms of what is causing the buzzing. It could be a warped neck, which would be fixed by a truss rod adjustment. Also, the action could be too low, meaning the strings are too close to the neck, so the string hits other frets when you play it creating a buzzing problem. Or, it could be electronics, if you have an electric. These problems are easily fixable, but if you have a nice instrument you want it in the hands of a professional.How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?With the strings off the guitar, you will use a straight edge across the frets. The instruction manual will give you a clearance at a certain fret, you will adjust the truss until those clearances are met. If you haven't done it before, I would take to your guitar shop and have them do it, it won't cost much and you will learn how to do it next time.How do I adjust the truss bar on an Ibanez guitar to get rid of a buzzing noise?the bolt at the top of the guitar, on the head, its next to the nut. get the appropriate allen wrench i believe you need, and twist it until the neck of the guitar isnt bowed any more.
How can I adjust the hop up on my air soft gun with out dis assembling the gun?
Crossman Stinger p9. When shot curves up and to the right. Severly. Every once in a wile it is normal. But 3/4 of the time its ridiculous. Can I adjust it without takinga apart the gun.How can I adjust the hop up on my air soft gun with out dis assembling the gun?no unless you have a hop up button check you manual.
How do you adjust a power seat if there was a manual seat there before?
I replaced my broken manual '95 dodge caravan driver's seat w/ a power '99 driver's seat. The wires underneath the seat don't match. Is there an adaptor to make these work together? Is there some way to manually adjust the seat? Is there any problem not having the wire from the floor of the van connected to the seat?How do you adjust a power seat if there was a manual seat there before?you don't need an adapter if had power seats to begin with,you just need the part of the harness that the other seats came from and cut and splice it on the existing wiring harness this way you,ll get power to it,you,ll need the wiring diagrams though for both vehicles to know what wires to hook up though,but really there isn't much to do on that one,power seats are one of the easiest things there is to wire up,most just have a two wire plug one positive wire and one ground wire,on a power seat the only way to adjust it is by running a power source to it,good luck.EDIT if you never had power seat to begin with you may not have the needed wires to install one with,so you,ll probably have to run some power wires to it,good luck.How do you adjust a power seat if there was a manual seat there before?your very welcome.
Report Abuse
How do you adjust a power seat if there was a manual seat there before?Nope - It's power or nothing. No adapter I've ever seen, %26amp; the wires coming-out of the floor carpet will be fine as they are. You should be able to adapt the new seat wiring to the van wiring with a bit of work.How do I adjust the carburator on my gas edger?
My craftsman edger has a 3 hp gas motor that has gone out of adjustment. The engine will not idle and although I can get the engine to run it constantly %26quot;surges%26quot; revving and then idling back in 1-2 sec intervals. I have only 1 needle adjust screw in the bowl of the carb but can't seem to get it set at a level that will both enable easy idling and revving to cut. Truthfully, I don't know for sure if the adjustment is the cause of the surging or if it's something else (vaccuum?) but any input would be appreciated.How do I adjust the carburator on my gas edger?Spray some brake cleaner or carb cleaner....etc. around the seals and see if it affects the engine.
It sounds like you may have some trash in the carb though... take it off and apart and blow it out with compressed air and carb cleaner through any and all holes you see. The setting should be 1.5 turns out from all the way in snug... as a baseline. You have to fine tune it when its warmed up till it revs up and down with little to no hesitation.
It sounds like you may have some trash in the carb though... take it off and apart and blow it out with compressed air and carb cleaner through any and all holes you see. The setting should be 1.5 turns out from all the way in snug... as a baseline. You have to fine tune it when its warmed up till it revs up and down with little to no hesitation.
How can I adjust the water flow on my Magnum 350 canister filter?
Should I use the on/off switch (moving it to the left) or adjust the white valve on the output hose? I don't want to damage the filter, but sometimes the flow is a bit much, especially at feeding time. I've been just turning it off for feeding. Thanks.How can I adjust the water flow on my Magnum 350 canister filter?I have that type of filter, and to be honest I don't think you can control the flow.live.com cemetery plot
How do I adjust the switch on a ceiling fan to suck the hot air out of my home?
I have a ceiling fan in my garage and want to adjust it to take the hot air out. Hey, I'm a female........need help.........thanks!How do I adjust the switch on a ceiling fan to suck the hot air out of my home?If your fan has a switch on it (usually above the blades on the motor housing) an easy way to remember which way it needs to be is---heat up/means put the switch up in the winter---cool down/ means put the switch down in the summer. Of course this is in the house where you run a heater or conditioner and you want the air to circulate to the best advantage, I'm not sure if it will help much in the garage.How do I adjust the switch on a ceiling fan to suck the hot air out of my home?Get a small step ladder and you will see a small switch usually located upper base which moves horizonatally back and forth. By moving it in opposite direction it will pull air up from the floor instead of shoving it down. Try it, youll like it.How do I adjust the switch on a ceiling fan to suck the hot air out of my home?There should be a switch on the side of the fan that toggles between moving the fan clock-wise and counter clock-wise. Depending on the pitch of the fan blades you want them to rotate in the direction that will pull hot air up. Most of the time this will be counter clock-wise. Not sure if a ceiling fan will really do what you檙e wanting, an attic or whole house fan is for this proposes.How do I adjust the switch on a ceiling fan to suck the hot air out of my home?A ceiling fan only circulates the air in a room; it does not add or remove air or heat.
To remove the heat from your home, you will need an exhaust fan, and a make-up air vent. If you have an old home (over 25 years), the make up air will come in through leaks under doors, windows, and electrical outlets. If you have a newer energy efficient home, you will need to cut a hole in the wall and put in a filter, or open a window or door.
To remove the heat, the exhaust fan should be at the highest point in your home, and the air outside should be colder than the air at this highest point. If it is not, you are just circulating fresh hot air, which is OK, but you aren't going to get a cooling effect.
If you don't want to permanently install a fan, you can get a window fan and install it on the sunny side of your house, pointing out. Open a window on the shady side of your house, turn on the fan, and the warmer air will be drawn out, cooler air will come in.How do I adjust the switch on a ceiling fan to suck the hot air out of my home?sucking air out of the room is not done with the switch. the switch is for speed control. to suck the air rather than blow you have to change the blade position.How do I adjust the switch on a ceiling fan to suck the hot air out of my home?On the fan itself there should be a pull switch to turn on and off the light fixture that is under the fan, and on the opposite side of the pull switch is a slide switch. That switch will change the direction of the blades. One way will draw the air down to warm up the room, and the other way will pull the air up to cool down the room. Good Luck it really is simple.
To remove the heat from your home, you will need an exhaust fan, and a make-up air vent. If you have an old home (over 25 years), the make up air will come in through leaks under doors, windows, and electrical outlets. If you have a newer energy efficient home, you will need to cut a hole in the wall and put in a filter, or open a window or door.
To remove the heat, the exhaust fan should be at the highest point in your home, and the air outside should be colder than the air at this highest point. If it is not, you are just circulating fresh hot air, which is OK, but you aren't going to get a cooling effect.
If you don't want to permanently install a fan, you can get a window fan and install it on the sunny side of your house, pointing out. Open a window on the shady side of your house, turn on the fan, and the warmer air will be drawn out, cooler air will come in.How do I adjust the switch on a ceiling fan to suck the hot air out of my home?sucking air out of the room is not done with the switch. the switch is for speed control. to suck the air rather than blow you have to change the blade position.How do I adjust the switch on a ceiling fan to suck the hot air out of my home?On the fan itself there should be a pull switch to turn on and off the light fixture that is under the fan, and on the opposite side of the pull switch is a slide switch. That switch will change the direction of the blades. One way will draw the air down to warm up the room, and the other way will pull the air up to cool down the room. Good Luck it really is simple.
How do you adjust the idle on a 2006 Mitsubishi Eclipse?
My car's idle is out of wack and needs to be raised just a tad more. Is it possible to adjust it without visiting the stealership?How do you adjust the idle on a 2006 Mitsubishi Eclipse?the onboard computer adjust idle. just what symptom are you having? and it's probably under warranty. why would you fool around with it?How do you adjust the idle on a 2006 Mitsubishi Eclipse?yeah your gonna need to take her to the stealership, you should still have some warranty left. there isnt an idol adjuster for the 06 eclipses.How do you adjust the idle on a 2006 Mitsubishi Eclipse?Adjust the computer or, tighten/loosen the thottle cableHow do you adjust the idle on a 2006 Mitsubishi Eclipse?I know for a fact the older models have an adjusting screw near the throttle you can adjust the idle there. Although, I'm not familiar with the newer models.
How do you adjust a ballcock on a commode so that it stops running?
Our commode only runs about once per hour. Surely there has to be a simple way to adjust the ballcock so that the commode is not calling for so much water.How do you adjust a ballcock on a commode so that it stops running?Check two things.
Be sure the flapper which seals the drain at the bottom, is not leaking. These become warped over time. This may allow water to seep, triggering the water supply.
If this isn't the problem, the ball cock may not be cutting off the supply.
At times I've taken the rod holding the ball and very carefully bent it downwards just a bit, use both hands. This allows the ball to cut off supply and prevent any continous flow.How do you adjust a ballcock on a commode so that it stops running?Usually you bend the ballcock arm downward to adjust the water level lower. But! It sounds like your loosing water and every so often the ball cock drops and calls for water.I believe your flapper is not seating and allowing water to seep out slowly because it needs to be replaced. One more possibility is the ball has water in it screw it off and shake it you'll hear the water swishing around,if so replace it.How do you adjust a ballcock on a commode so that it stops running?It could be the rubber flapper that seats to close the water off inside is filled with sediment or **** of some kind;
Try cleaning it really well and check to be sure it isn*t dented or damaged somehow that could stop it from sealing properly. I just fixed our yesterday by doing that and then putting petroleum jelly all around the rim so that it seats really tight. Works fine now.How do you adjust a ballcock on a commode so that it stops running?there is a screw on the top of the float rod at the top of the water fill control, you can tighten this screw a little and the water will cut off sooner! Good Luck!
Be sure the flapper which seals the drain at the bottom, is not leaking. These become warped over time. This may allow water to seep, triggering the water supply.
If this isn't the problem, the ball cock may not be cutting off the supply.
At times I've taken the rod holding the ball and very carefully bent it downwards just a bit, use both hands. This allows the ball to cut off supply and prevent any continous flow.How do you adjust a ballcock on a commode so that it stops running?Usually you bend the ballcock arm downward to adjust the water level lower. But! It sounds like your loosing water and every so often the ball cock drops and calls for water.I believe your flapper is not seating and allowing water to seep out slowly because it needs to be replaced. One more possibility is the ball has water in it screw it off and shake it you'll hear the water swishing around,if so replace it.How do you adjust a ballcock on a commode so that it stops running?It could be the rubber flapper that seats to close the water off inside is filled with sediment or **** of some kind;
Try cleaning it really well and check to be sure it isn*t dented or damaged somehow that could stop it from sealing properly. I just fixed our yesterday by doing that and then putting petroleum jelly all around the rim so that it seats really tight. Works fine now.How do you adjust a ballcock on a commode so that it stops running?there is a screw on the top of the float rod at the top of the water fill control, you can tighten this screw a little and the water will cut off sooner! Good Luck!
How do I adjust my brakes on a road bike?
It's fairly new bike and the brakes are spongy, they need to be pressed almost all the way to the handlebars to stop. I assume it's just the cables stretching, but I don;t know how to adjust them.How do I adjust my brakes on a road bike?twist the barrel adjuster on the brake lever. careful not to pull it too far out. this should bring yuor pads in a good distance, if they are still centered on the rim.How do I adjust my brakes on a road bike?try this site:
http://www.bikewebsite.com/bicycle-bra.hHow do I adjust my brakes on a road bike?If the bike is new, you don't need to do anything complicated. The other answer already referenced a good site. Go there, and know that you have %26quot;sidepull%26quot; brakes.
Look at the calipers. Just above where the cable attaches to the calipers, you're going to see a barrel adjuster. Turn the adjuster counterclockwise as you look down on it. This should back the adjuster out toward you, and tighten.
Try the brakes....they should be better.
P.S. make sure the lever that opens the brakes so you can get your tire off easily is closed. It's a cam-like thing, and is the rear-most piece of metal on the calipers.
http://www.bikewebsite.com/bicycle-bra.hHow do I adjust my brakes on a road bike?If the bike is new, you don't need to do anything complicated. The other answer already referenced a good site. Go there, and know that you have %26quot;sidepull%26quot; brakes.
Look at the calipers. Just above where the cable attaches to the calipers, you're going to see a barrel adjuster. Turn the adjuster counterclockwise as you look down on it. This should back the adjuster out toward you, and tighten.
Try the brakes....they should be better.
P.S. make sure the lever that opens the brakes so you can get your tire off easily is closed. It's a cam-like thing, and is the rear-most piece of metal on the calipers.
Subscribe to:
Posts
(Atom)